Industrial
-
€27.99
- Measures temperature with a thermocouple
- Supports B, E, J, K, N, R and T type
-
€249.98
- 80x60 pixel thermal imaging camera
- Measurement range -10°C to 450°C
- Uses FLIR Lepton with radiometry and shutter
- High Contrast Image with 8.6Hz and 8 bit resolution (for display)
- Temperature Image with 4.5Hz and 16 bit resolution (for scientific calculations)
- Definable spotmeter with min, max, mean temperature measurement
- Automatic shutter control
-
€6.99
- Galvanically isolated switching of large AC or DC loads
- For example: motors, pumps and lamps
- Bricklet controls Solid State Relays (SSR)
- The offered SSRs can switch up to 380V/25A AC or 50V/80A DC
- PWM possible (dimming of lamps, control speed of motors)
- Galvanically isolated switching of large AC or DC loads
-
€34.99
- Supports low-level RS485 as well as Modbus RTU master/slave
- Modbus RTU implementation is fully compliant for reading and writing of coils and registers
- Supports full- and half-duplex
- Configurable baudrate, parity, stop bits and word length
- Switchable 120 Ohm termination
-
€21.99
- Sends and receives serial data
- Provides RS-232 and UART-TTL interface
- Configurable baudrate, parity, stop bits, word length and flow control
-
€49.99
- Measures Particulate Matter concentration
- Measures in µg/m³ for differenz sizes
- Distinguishable particle sizes: PM1.0, PM2.5 and PM10
- Integrated fan for air flow
-
€14.99
- 1-wire communication with any 1-wire capable device
- Offers high-level commands (bus search, reset, write, read, write command)
- Supports 3.3V, 5V and external supply voltage
- Supports up to 64 1-wire devices simultaneously
-
€29.99
- Can read and write NFC Forum Type 1, 2, 3, 4, 5 and Mifare Classic tags.
- NDEF definitions can be directly read/written with API.
- Supports NFC P2P mode
- Supports card emulation mode
- Range is restricted to 10cm (3.94")
-
€39.98
- Linear Potentiometer with 100mm fader travel
- Fader position can be controlled by user and with a motor
- No additional power supply necessary
- Automatic calibration
-
€17.99
- Measures output of load cells
- 24bit ADC for high resolution
- Up to 80 weight measurements per second
-
€19.99
- Galvanically isolates the power and data lines
- Can be used between any Brick and any Bricklet with a 7 pole connector
-
€16.99
- 16-channel digital input/output
- Switchable logic voltage 3.3V or 5V*
- Configurable pull-ups and interrupts
-
€34.99
- 4 Channel Solid State Relay
- Switch up to 30V with 0.6A
- Galvanically isolated
-
€27.99
- Supports Pt100 and Pt1000 sensors
- Supports 2-wire, 3-wire and 4-wire type
- Measures temperature with 0.05% accuracy at the full scale of -246 to 849°C
- Resolution of 0.03125°C (15bit), output in 0.01°C steps
-
€16.99
- Two relays for switching AC/DC devices
- Switches up to 240VAC/10A and 30VDC/7A
-
€40.00
- Independently measures two voltages between -35V and +35V (DC)
- 24bit ADC for high resolution
- Individually calibrated
- Full-scale accuracy of 0.1% / ±4mV
- Up to 976 samples per second
-
€11.98
- Two solid state relays for switching AC devices
- Switches up to 240VAC/1.2A (with max 12A surge current)
- Switching done during zero-crossing
-
€16.99
- Two inputs that can detect the presence of 230VAC mains voltage
- State LED per input
-
€24.99
- Precision current sensor, measures currents between 0 and 22.5mA
- Can read out any IEC 60381-1 type 2 and type 3 sensor
- High accuracy (0.15%), resolution (up to 0.172µA) and sample rate (up to 240 SPS)
- It is possible to detect if a sensor is connected/faulty
-
€21.99
- 4 channel digital output
- Output voltages up to 36V
- Galvanically isolated
- Status LED per channel
- PWM output with frequency up to 40kHz
-
€16.99
- 4 channel digital input
- Input voltages up to 36V (DC)
- Galvanically isolated
-
€34.99
- 4 channel galvanically isolated frequency counter
- Configurable edge count per channel
- Measures duty cycle, period and frequency per channel
- Frequency range from 0.03Hz to 4MHz
- Time resolution up to 10.4ns and frequency resolution up to 0.03Hz
-
€34.99
- Simultaneous programmable voltage and current output
- Outputs voltage between 0V and 10V (IEC 60381-1)
- Outputs current between 0mA and 24mA (IEC 60381-2)
- No external power supply necessary
-
€24.99
- Sends and receives data through CAN bus
- Configurable baudrate, modes and filters