TCP/IP - Joystick Bricklet 2.0¶

Basic Functions¶

BrickletJoystickV2.get_position¶

Function ID:	1
Request:	empty payload
Response:	x – Type: int16, Range: [-100 to 100] y – Type: int16, Range: [-100 to 100]

Returns the position of the joystick. The middle position of the joystick is x=0, y=0. The returned values are averaged and calibrated (see calibrate).

If you want to get the position periodically, it is recommended to use the CALLBACK_POSITION callback and set the period with set_position_callback_configuration.

BrickletJoystickV2.is_pressed¶

Function ID:	2
Request:	empty payload
Response:	pressed – Type: bool

Returns true if the button is pressed and false otherwise.

If you want to get the press-state periodically, it is recommended to use the CALLBACK_PRESSED callback and set the period with set_pressed_callback_configuration.

Advanced Functions¶

BrickletJoystickV2.calibrate¶

Function ID:	3
Request:	empty payload
Response:	no response

Calibrates the middle position of the joystick. If your Joystick Bricklet 2.0 does not return x=0 and y=0 in the middle position, call this function while the joystick is standing still in the middle position.

The resulting calibration will be saved in non-volatile memory, thus you only have to calibrate it once.

BrickletJoystickV2.get_spitfp_error_count¶

Function ID:	234
Request:	empty payload
Response:	error_count_ack_checksum – Type: uint32, Range: [0 to 232 - 1] error_count_message_checksum – Type: uint32, Range: [0 to 232 - 1] error_count_frame – Type: uint32, Range: [0 to 232 - 1] error_count_overflow – Type: uint32, Range: [0 to 232 - 1]

Returns the error count for the communication between Brick and Bricklet.

The errors are divided into

• ACK checksum errors,
• message checksum errors,
• framing errors and
• overflow errors.

The errors counts are for errors that occur on the Bricklet side. All Bricks have a similar function that returns the errors on the Brick side.

BrickletJoystickV2.set_status_led_config¶

Function ID:	239
Request:	config – Type: uint8, Range: See meanings, Default: 3
Response:	no response

Sets the status LED configuration. By default the LED shows communication traffic between Brick and Bricklet, it flickers once for every 10 received data packets.

You can also turn the LED permanently on/off or show a heartbeat.

If the Bricklet is in bootloader mode, the LED is will show heartbeat by default.

The following meanings are defined for the elements of this function:

For config:

• 0 = Off
• 1 = On
• 2 = Show Heartbeat
• 3 = Show Status

BrickletJoystickV2.get_status_led_config¶

Function ID:	240
Request:	empty payload
Response:	config – Type: uint8, Range: See meanings, Default: 3

Returns the configuration as set by set_status_led_config

The following meanings are defined for the elements of this function:

For config:

• 0 = Off
• 1 = On
• 2 = Show Heartbeat
• 3 = Show Status

BrickletJoystickV2.get_chip_temperature¶

Function ID:	242
Request:	empty payload
Response:	temperature – Type: int16, Unit: 1 °C, Range: [-215 to 215 - 1]

Returns the temperature as measured inside the microcontroller. The value returned is not the ambient temperature!

The temperature is only proportional to the real temperature and it has bad accuracy. Practically it is only useful as an indicator for temperature changes.

BrickletJoystickV2.reset¶

Function ID:	243
Request:	empty payload
Response:	no response

Calling this function will reset the Bricklet. All configurations will be lost.

After a reset you have to create new device objects, calling functions on the existing ones will result in undefined behavior!

BrickletJoystickV2.get_identity¶

Function ID:	255
Request:	empty payload
Response:	uid – Type: char[8] connected_uid – Type: char[8] position – Type: char, Range: ['a' to 'h', 'z'] hardware_version – Type: uint8[3] 0: major – Type: uint8, Range: [0 to 255] 1: minor – Type: uint8, Range: [0 to 255] 2: revision – Type: uint8, Range: [0 to 255] firmware_version – Type: uint8[3] 0: major – Type: uint8, Range: [0 to 255] 1: minor – Type: uint8, Range: [0 to 255] 2: revision – Type: uint8, Range: [0 to 255] device_identifier – Type: uint16, Range: [0 to 216 - 1]

Returns the UID, the UID where the Bricklet is connected to, the position, the hardware and firmware version as well as the device identifier.

The position can be 'a', 'b', 'c', 'd', 'e', 'f', 'g' or 'h' (Bricklet Port). A Bricklet connected to an Isolator Bricklet is always at position 'z'.

The device identifier numbers can be found here. 

Callback Configuration Functions¶

BrickletJoystickV2.set_position_callback_configuration¶

Function ID:	4
Request:	period – Type: uint32, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0 value_has_to_change – Type: bool, Default: false
Response:	no response

The period is the period with which the CALLBACK_POSITION callback is triggered periodically. A value of 0 turns the callback off.

If the value has to change-parameter is set to true, the callback is only triggered after at least one of the values has changed. If the values didn't change within the period, the callback is triggered immediately on change.

If it is set to false, the callback is continuously triggered with the period, independent of the value.

BrickletJoystickV2.get_position_callback_configuration¶

Function ID:	5
Request:	empty payload
Response:	period – Type: uint32, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0 value_has_to_change – Type: bool, Default: false

Returns the callback configuration as set by set_position_callback_configuration.

BrickletJoystickV2.set_pressed_callback_configuration¶

Function ID:	7
Request:	period – Type: uint32, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0 value_has_to_change – Type: bool, Default: false
Response:	no response

The period is the period with which the CALLBACK_PRESSED callback is triggered periodically. A value of 0 turns the callback off.

If the value has to change-parameter is set to true, the callback is only triggered after at least one of the values has changed. If the values didn't change within the period, the callback is triggered immediately on change.

If it is set to false, the callback is continuously triggered with the period, independent of the value.

BrickletJoystickV2.get_pressed_callback_configuration¶

Function ID:	8
Request:	empty payload
Response:	period – Type: uint32, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0 value_has_to_change – Type: bool, Default: false

Returns the callback configuration as set by set_pressed_callback_configuration.

Callbacks¶

BrickletJoystickV2.CALLBACK_POSITION¶

Function ID:	6
Response:	x – Type: int16, Range: [-100 to 100] y – Type: int16, Range: [-100 to 100]

This callback is triggered periodically according to the configuration set by set_position_callback_configuration.

The response values are the same as with get_position.

BrickletJoystickV2.CALLBACK_PRESSED¶

Function ID:	9
Response:	pressed – Type: bool

This callback is triggered periodically according to the configuration set by set_pressed_callback_configuration.

The response values are the same as with is_pressed.

Internal Functions¶

Internal functions are used for maintenance tasks such as flashing a new firmware of changing the UID of a Bricklet. These task should be performed using Brick Viewer instead of using the internal functions directly.

BrickletJoystickV2.set_bootloader_mode¶

Function ID:	235
Request:	mode – Type: uint8, Range: See meanings
Response:	status – Type: uint8, Range: See meanings

Sets the bootloader mode and returns the status after the requested mode change was instigated.

You can change from bootloader mode to firmware mode and vice versa. A change from bootloader mode to firmware mode will only take place if the entry function, device identifier and CRC are present and correct.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

The following meanings are defined for the elements of this function:

For mode:

• 0 = Bootloader
• 1 = Firmware
• 2 = Bootloader Wait For Reboot
• 3 = Firmware Wait For Reboot
• 4 = Firmware Wait For Erase And Reboot

For status:

• 0 = OK
• 1 = Invalid Mode
• 2 = No Change
• 3 = Entry Function Not Present
• 4 = Device Identifier Incorrect
• 5 = CRC Mismatch

BrickletJoystickV2.get_bootloader_mode¶

Function ID:	236
Request:	empty payload
Response:	mode – Type: uint8, Range: See meanings

Returns the current bootloader mode, see set_bootloader_mode.

The following meanings are defined for the elements of this function:

For mode:

• 0 = Bootloader
• 1 = Firmware
• 2 = Bootloader Wait For Reboot
• 3 = Firmware Wait For Reboot
• 4 = Firmware Wait For Erase And Reboot

BrickletJoystickV2.set_write_firmware_pointer¶

Function ID:	237
Request:	pointer – Type: uint32, Unit: 1 B, Range: [0 to 232 - 1]
Response:	no response

Sets the firmware pointer for write_firmware. The pointer has to be increased by chunks of size 64. The data is written to flash every 4 chunks (which equals to one page of size 256).

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

BrickletJoystickV2.write_firmware¶

Function ID:	238
Request:	data – Type: uint8[64], Range: [0 to 255]
Response:	status – Type: uint8, Range: [0 to 255]

Writes 64 Bytes of firmware at the position as written by set_write_firmware_pointer before. The firmware is written to flash every 4 chunks.

You can only write firmware in bootloader mode.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

BrickletJoystickV2.write_uid¶

Function ID:	248
Request:	uid – Type: uint32, Range: [0 to 232 - 1]
Response:	no response

Writes a new UID into flash. If you want to set a new UID you have to decode the Base58 encoded UID string into an integer first.

We recommend that you use Brick Viewer to change the UID.

BrickletJoystickV2.read_uid¶

Function ID:	249
Request:	empty payload
Response:	uid – Type: uint32, Range: [0 to 232 - 1]

Returns the current UID as an integer. Encode as Base58 to get the usual string version.