Deutsch
English
Menu
Software / API Bindings / Go / API Reference and Examples / Bricks / ESP32 Brick

Go - ESP32 Brick

This is the description of the Go API bindings for the ESP32 Brick. General information and technical specifications for the ESP32 Brick are summarized in its hardware description.

An installation guide for the Go API bindings is part of their general description. Additional documentation can be found on godoc.org.

API

The ESP32 Brick API is defined in the package github.com/Tinkerforge/go-api-bindings/esp32_brick

Nearly every function of the Go bindings can return an ipconnection.DeviceError, implementing the error interface. The error can have one of the following values:

  • ipconnection.DeviceErrorSuccess = 0
  • ipconnection.DeviceErrorInvalidParameter = 1
  • ipconnection.DeviceErrorFunctionNotSupported = 2
  • ipconnection.DeviceErrorUnknownError = 3

which correspond to the values returned from Bricks and Bricklets.

All functions listed below are thread-safe.

Advanced Functions

func (*ESP32Brick) GetIdentity() (uid string, connectedUid string, position rune, hardwareVersion [3]uint8, firmwareVersion [3]uint8, deviceIdentifier uint16, err error)
Returns:
  • uid – Type: string, Length: up to 8
  • connectedUid – Type: string, Length: up to 8
  • position – Type: rune, Range: ['0' to '8']
  • hardwareVersion – Type: [3]uint8
    • 0: major – Type: uint8, Range: [0 to 255]
    • 1: minor – Type: uint8, Range: [0 to 255]
    • 2: revision – Type: uint8, Range: [0 to 255]
  • firmwareVersion – Type: [3]uint8
    • 0: major – Type: uint8, Range: [0 to 255]
    • 1: minor – Type: uint8, Range: [0 to 255]
    • 2: revision – Type: uint8, Range: [0 to 255]
  • deviceIdentifier – Type: uint16, Range: [0 to 216 - 1]
  • err – Type: error

Returns the UID, the UID where the Brick is connected to, the position, the hardware and firmware version as well as the device identifier.

The position is the position in the stack from '0' (bottom) to '8' (top).

The device identifier numbers can be found here. There is also a constant for the device identifier of this Brick.

Virtual Functions

Virtual functions don't communicate with the device itself, but operate only on the API bindings device object. They can be called without the corresponding IP Connection object being connected.

func (*ESP32Brick) GetAPIVersion() (apiVersion [3]uint8, err error)
Returns:
  • apiVersion – Type: [3]uint8
    • 0: major – Type: uint8, Range: [0 to 255]
    • 1: minor – Type: uint8, Range: [0 to 255]
    • 2: revision – Type: uint8, Range: [0 to 255]
  • err – Type: error

Returns the version of the API definition implemented by this API bindings. This is neither the release version of this API bindings nor does it tell you anything about the represented Brick or Bricklet.

func (*ESP32Brick) GetResponseExpected(functionId uint8) (responseExpected bool, err error)
Parameters:
  • functionId – Type: uint8, Range: See constants
Returns:
  • responseExpected – Type: bool
  • err – Type: error

Returns the response expected flag for the function specified by the function ID parameter. It is true if the function is expected to send a response, false otherwise.

For getter functions this is enabled by default and cannot be disabled, because those functions will always send a response. For callback configuration functions it is enabled by default too, but can be disabled by SetResponseExpected(). For setter functions it is disabled by default and can be enabled.

Enabling the response expected flag for a setter function allows to detect timeouts and other error conditions calls of this setter as well. The device will then send a response for this purpose. If this flag is disabled for a setter function then no response is sent and errors are silently ignored, because they cannot be detected.

The following constants are available for this function:

For functionId:

func (*ESP32Brick) SetResponseExpected(functionId uint8, responseExpected bool) (err error)
Parameters:
  • functionId – Type: uint8, Range: See constants
  • responseExpected – Type: bool
Returns:
  • err – Type: error

Changes the response expected flag of the function specified by the function ID parameter. This flag can only be changed for setter (default value: false) and callback configuration functions (default value: true). For getter functions it is always enabled.

Enabling the response expected flag for a setter function allows to detect timeouts and other error conditions calls of this setter as well. The device will then send a response for this purpose. If this flag is disabled for a setter function then no response is sent and errors are silently ignored, because they cannot be detected.

The following constants are available for this function:

For functionId:

func (*ESP32Brick) SetResponseExpectedAll(responseExpected bool) (err error)
Parameters:
  • responseExpected – Type: bool
Returns:
  • err – Type: error

Changes the response expected flag for all setter and callback configuration functions of this device at once.

Constants

esp32_brick.DeviceIdentifier

This constant is used to identify a ESP32 Brick.

The GetIdentity() function and the (*IPConnection) RegisterEnumerateCallback callback of the IPConnection have a deviceIdentifier parameter to specify the Brick's or Bricklet's type.

esp32_brick.DeviceDisplayName

This constant represents the human readable name of a ESP32 Brick.