Deutsch
English
Menu
Software / API Bindings / Mathematica / API Reference and Examples / Bricklets / Performance DC Bricklet

Mathematica - Performance DC Bricklet

This is the description of the Mathematica API bindings for the Performance DC Bricklet. General information and technical specifications for the Performance DC Bricklet are summarized in its hardware description.

An installation guide for the Mathematica API bindings is part of their general description.

Examples

The example code below is Public Domain (CC0 1.0).

Configuration

Download (ExampleConfiguration.nb)

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Needs["NETLink`"]
LoadNETAssembly["Tinkerforge",NotebookDirectory[]<>"../../.."]

host="localhost"
port=4223
uid="XYZ"(*Change XYZ to the UID of your Performance DC Bricklet*)

(*Create IPConnection and device object*)
ipcon=NETNew["Tinkerforge.IPConnection"]
pdc=NETNew["Tinkerforge.BrickletPerformanceDC",uid,ipcon]
ipcon@Connect[host,port]

pdc@SetDriveMode[Tinkerforge`BrickletPerformanceDC`DRIVEUMODEUDRIVEUCOAST]
pdc@SetPWMFrequency[10000](*Use PWM frequency of 10 kHz*)
pdc@SetMotion[4096,4096](*Slow ac-/deceleration (12.5 %/s)*)
pdc@SetVelocity[32767](*Full speed forward (100 %)*)
pdc@SetEnabled[True](*Enable motor power*)

Input["Click OK to exit"]

(*Stop motor before disabling motor power*)
pdc@SetMotion[4096,16384](*Fast decceleration (50 %/s) for stopping*)
pdc@SetVelocity[0](*Request motor stop*)
Pause[2](*Wait for motor to actually stop: velocity (100 %) / decceleration (50 %/s) = 2 s*)
pdc@SetEnabled[False](*Disable motor power*)

ipcon@Disconnect[]
ReleaseNETObject[pdc]
ReleaseNETObject[ipcon]

Callback

Download (ExampleCallback.nb)

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Needs["NETLink`"]
LoadNETAssembly["Tinkerforge",NotebookDirectory[]<>"../../.."]

host="localhost"
port=4223
uid="XYZ"(*Change XYZ to the UID of your Performance DC Bricklet*)

(*Create IPConnection and device object*)
ipcon=NETNew["Tinkerforge.IPConnection"]
pdc=NETNew["Tinkerforge.BrickletPerformanceDC",uid,ipcon]
ipcon@Connect[host,port]

(*Use velocity reached callback to swing back and forth*)
(*between full speed forward and full speed backward*)
VelocityReachedCB[sender_,velocity_]:=
 Module[{},
  If[velocity==32767,
   Print["Velocity: Full speed forward, now turning backward"];
   sender@SetVelocity[-32767]
  ];
  If[velocity==-32767,
   Print["Velocity: Full speed backward, now turning forward"];
   sender@SetVelocity[32767]
  ]
 ]

AddEventHandler[pdc@VelocityReachedCallback,VelocityReachedCB]

(*Enable velocity reached callback*)
pdc@SetVelocityReachedCallbackConfiguration[True]

(*The acceleration has to be smaller or equal to the maximum*)
(*acceleration of the DC motor, otherwise the velocity reached*)
(*callback will be called too early*)
pdc@SetMotion[4096,4096](*Slow acceleration (12.5 %/s)*)
pdc@SetVelocity[32767](*Full speed forward (100 %)*)

(*Enable motor power*)
pdc@SetEnabled[True]

Input["Click OK to exit"]

(*Stop motor before disabling motor power*)
pdc@SetMotion[4096,16384](*Fast decceleration (50 %/s) for stopping*)
pdc@SetVelocity[0](*Request motor stop*)
Pause[2](*Wait for motor to actually stop: velocity (100 %) / decceleration (50 %/s) = 2 s*)
pdc@SetEnabled[False](*Disable motor power*)

ipcon@Disconnect[]
ReleaseNETObject[pdc]
ReleaseNETObject[ipcon]

API

Generally, every function of the Mathematica bindings that returns a value can throw a Tinkerforge.TimeoutException. This exception gets thrown if the device did not respond. If a cable based connection is used, it is unlikely that this exception gets thrown (assuming nobody plugs the device out). However, if a wireless connection is used, timeouts will occur if the distance to the device gets too big.

Since .NET/Link does not support multiple return values directly, we use the out keyword to return multiple values from a function. For further information about the out keyword in .NET/Link see the corresponding Mathematica .NET/Link documentation.

The namespace for all Brick/Bricklet bindings and the IPConnection is Tinkerforge.*.

Basic Functions

BrickletPerformanceDC[uid, ipcon] → performanceDC
Parameters:
  • uid – Type: String
  • ipcon – Type: NETObject[IPConnection]
Returns:
  • performanceDC – Type: NETObject[BrickletPerformanceDC]

Creates an object with the unique device ID uid:

performanceDC=NETNew["Tinkerforge.BrickletPerformanceDC","YOUR_DEVICE_UID",ipcon]

This object can then be used after the IP Connection is connected.

The .NET runtime has built-in garbage collection that frees objects that are no longer in use by a program. But because Mathematica can not automatically tell when a Mathematica "program" doesn't use a .NET object anymore, this has to be done by the program. For this the ReleaseNETObject[] function is used in the examples.

For further information about object management in .NET/Link see the corresponding Mathematica .NET/Link documentation.

BrickletPerformanceDC@SetEnabled[enabled] → Null
Parameters:
  • enabled – Type: True/False

Enables/Disables the driver chip. The driver parameters can be configured (velocity, acceleration, etc) before it is enabled.

BrickletPerformanceDC@GetEnabled[] → enabled
Returns:
  • enabled – Type: True/False, Default: False

Returns true if the driver chip is enabled, false otherwise.

BrickletPerformanceDC@SetVelocity[velocity] → Null
Parameters:
  • velocity – Type: Integer, Unit: 100/32767 %, Range: [-215 + 1 to 215 - 1], Default: 0

Sets the velocity of the motor. Whereas -32767 is full speed backward, 0 is stop and 32767 is full speed forward. Depending on the acceleration (see SetMotion[]), the motor is not immediately brought to the velocity but smoothly accelerated.

The velocity describes the duty cycle of the PWM with which the motor is controlled, e.g. a velocity of 3277 sets a PWM with a 10% duty cycle. You can not only control the duty cycle of the PWM but also the frequency, see SetPWMFrequency[].

BrickletPerformanceDC@GetVelocity[] → velocity
Returns:
  • velocity – Type: Integer, Unit: 100/32767 %, Range: [-215 + 1 to 215 - 1], Default: 0

Returns the velocity as set by SetVelocity[].

BrickletPerformanceDC@GetCurrentVelocity[] → velocity
Returns:
  • velocity – Type: Integer, Unit: 100/32767 %, Range: [-215 + 1 to 215 - 1], Default: 0

Returns the current velocity of the motor. This value is different from GetVelocity[] whenever the motor is currently accelerating to a goal set by SetVelocity[].

BrickletPerformanceDC@SetMotion[acceleration, deceleration] → Null
Parameters:
  • acceleration – Type: Integer, Unit: 100/32767 %/s, Range: [0 to 216 - 1], Default: 10000
  • deceleration – Type: Integer, Unit: 100/32767 %/s, Range: [0 to 216 - 1], Default: 10000

Sets the acceleration and deceleration of the motor. It is given in velocity/s. An acceleration of 10000 means, that every second the velocity is increased by 10000 (or about 30% duty cycle).

For example: If the current velocity is 0 and you want to accelerate to a velocity of 16000 (about 50% duty cycle) in 10 seconds, you should set an acceleration of 1600.

If acceleration and deceleration is set to 0, there is no speed ramping, i.e. a new velocity is immediately given to the motor.

BrickletPerformanceDC@GetMotion[out acceleration, out deceleration] → Null
Output Parameters:
  • acceleration – Type: Integer, Unit: 100/32767 %/s, Range: [0 to 216 - 1], Default: 10000
  • deceleration – Type: Integer, Unit: 100/32767 %/s, Range: [0 to 216 - 1], Default: 10000

Returns the acceleration/deceleration as set by SetMotion[].

BrickletPerformanceDC@FullBrake[] → Null

Executes an active full brake.

Warning

This function is for emergency purposes, where an immediate brake is necessary. Depending on the current velocity and the strength of the motor, a full brake can be quite violent.

Call SetVelocity[] with 0 if you just want to stop the motor.

BrickletPerformanceDC@GetPWMFrequency[] → frequency
Returns:
  • frequency – Type: Integer, Unit: 1 Hz, Range: [1 to 20000], Default: 15000

Returns the PWM frequency as set by SetPWMFrequency[].

BrickletPerformanceDC@GetPowerStatistics[out voltage, out current, out temperature] → Null
Output Parameters:
  • voltage – Type: Integer, Unit: 1 mV, Range: [0 to 216 - 1]
  • current – Type: Integer, Unit: 1 mA, Range: [0 to 216 - 1]
  • temperature – Type: Integer, Unit: 1/10 °, Range: [-215 to 215 - 1]

Returns input voltage, current usage and temperature of the driver.

BrickletPerformanceDC@SetThermalShutdown[temperature] → Null
Parameters:
  • temperature – Type: Integer, Unit: 1 °, Range: [0 to 255], Default: 125

Sets a temperature threshold that is used for thermal shutdown.

Additionally to this user defined threshold the driver chip will shut down at a temperature of 150°C.

If a thermal shutdown is triggered the driver is disabled and has to be explicitly re-enabled with SetEnabled[].

BrickletPerformanceDC@GetThermalShutdown[] → temperature
Returns:
  • temperature – Type: Integer, Unit: 1 °, Range: [0 to 255]

Returns the thermal shutdown temperature as set by SetThermalShutdown[].

BrickletPerformanceDC@SetGPIOConfiguration[channel, debounce, stopDeceleration] → Null
Parameters:
  • channel – Type: Integer, Range: [0 to 1]
  • debounce – Type: Integer, Unit: 1 ms, Range: [0 to 216 - 1], Default: 200
  • stopDeceleration – Type: Integer, Unit: 100/32767 %/s, Range: [0 to 216 - 1], Default: 216 - 1

Sets the GPIO configuration for the given channel. You can configure a debounce and the deceleration that is used if the action is configured as normal stop. See SetGPIOAction[].

BrickletPerformanceDC@GetGPIOConfiguration[channel, out debounce, out stopDeceleration] → Null
Parameters:
  • channel – Type: Integer, Range: [0 to 1]
Output Parameters:
  • debounce – Type: Integer, Unit: 1 ms, Range: [0 to 216 - 1], Default: 200
  • stopDeceleration – Type: Integer, Unit: 100/32767 %/s, Range: [0 to 216 - 1], Default: 216 - 1

Returns the GPIO configuration for a channel as set by SetGPIOConfiguration[].

BrickletPerformanceDC@SetGPIOAction[channel, action] → Null
Parameters:
  • channel – Type: Integer, Range: [0 to 1]
  • action – Type: Integer, Range: See constants, Default: 0

Sets the GPIO action for the given channel.

The action can be a normal stop, a full brake or a callback. Each for a rising edge or falling edge. The actions are a bitmask they can be used at the same time. You can for example trigger a full brake and a callback at the same time or for rising and falling edge.

The deceleration speed for the normal stop can be configured with SetGPIOConfiguration[].

The following constants are available for this function:

For action:

  • BrickletPerformanceDC`GPIOUACTIONUNONE = 0
  • BrickletPerformanceDC`GPIOUACTIONUNORMALUSTOPURISINGUEDGE = 1
  • BrickletPerformanceDC`GPIOUACTIONUNORMALUSTOPUFALLINGUEDGE = 2
  • BrickletPerformanceDC`GPIOUACTIONUFULLUBRAKEURISINGUEDGE = 4
  • BrickletPerformanceDC`GPIOUACTIONUFULLUBRAKEUFALLINGUEDGE = 8
  • BrickletPerformanceDC`GPIOUACTIONUCALLBACKURISINGUEDGE = 16
  • BrickletPerformanceDC`GPIOUACTIONUCALLBACKUFALLINGUEDGE = 32
BrickletPerformanceDC@GetGPIOAction[channel] → action
Parameters:
  • channel – Type: Integer, Range: [0 to 1]
Returns:
  • action – Type: Integer, Range: See constants, Default: 0

Returns the GPIO action for a channel as set by SetGPIOAction[].

The following constants are available for this function:

For action:

  • BrickletPerformanceDC`GPIOUACTIONUNONE = 0
  • BrickletPerformanceDC`GPIOUACTIONUNORMALUSTOPURISINGUEDGE = 1
  • BrickletPerformanceDC`GPIOUACTIONUNORMALUSTOPUFALLINGUEDGE = 2
  • BrickletPerformanceDC`GPIOUACTIONUFULLUBRAKEURISINGUEDGE = 4
  • BrickletPerformanceDC`GPIOUACTIONUFULLUBRAKEUFALLINGUEDGE = 8
  • BrickletPerformanceDC`GPIOUACTIONUCALLBACKURISINGUEDGE = 16
  • BrickletPerformanceDC`GPIOUACTIONUCALLBACKUFALLINGUEDGE = 32
BrickletPerformanceDC@GetGPIOState[] → {gpioState1, gpioState2}
Returns:
  • gpioStatei – Type: True/False

Returns the GPIO state for both channels. True if the state is high and false if the state is low.

Advanced Functions

BrickletPerformanceDC@SetDriveMode[mode] → Null
Parameters:
  • mode – Type: Integer, Range: See constants, Default: 0

Sets the drive mode. Possible modes are:

  • 0 = Drive/Brake
  • 1 = Drive/Coast

These modes are different kinds of motor controls.

In Drive/Brake mode, the motor is always either driving or braking. There is no freewheeling. Advantages are: A more linear correlation between PWM and velocity, more exact accelerations and the possibility to drive with slower velocities.

In Drive/Coast mode, the motor is always either driving or freewheeling. Advantages are: Less current consumption and less demands on the motor and driver chip.

The following constants are available for this function:

For mode:

  • BrickletPerformanceDC`DRIVEUMODEUDRIVEUBRAKE = 0
  • BrickletPerformanceDC`DRIVEUMODEUDRIVEUCOAST = 1
BrickletPerformanceDC@GetDriveMode[] → mode
Returns:
  • mode – Type: Integer, Range: See constants, Default: 0

Returns the drive mode, as set by SetDriveMode[].

The following constants are available for this function:

For mode:

  • BrickletPerformanceDC`DRIVEUMODEUDRIVEUBRAKE = 0
  • BrickletPerformanceDC`DRIVEUMODEUDRIVEUCOAST = 1
BrickletPerformanceDC@SetPWMFrequency[frequency] → Null
Parameters:
  • frequency – Type: Integer, Unit: 1 Hz, Range: [1 to 20000], Default: 15000

Sets the frequency of the PWM with which the motor is driven. Often a high frequency is less noisy and the motor runs smoother. However, with a low frequency there are less switches and therefore fewer switching losses. Also with most motors lower frequencies enable higher torque.

If you have no idea what all this means, just ignore this function and use the default frequency, it will very likely work fine.

BrickletPerformanceDC@SetErrorLEDConfig[config] → Null
Parameters:
  • config – Type: Integer, Range: See constants, Default: 3

Configures the error LED to be either turned off, turned on, blink in heartbeat mode or show an error.

If the LED is configured to show errors it has three different states:

  • Off: No error present.
  • 1s interval blinking: Input voltage too low (below 6V).
  • 250ms interval blinking: Overtemperature or overcurrent.

The following constants are available for this function:

For config:

  • BrickletPerformanceDC`ERRORULEDUCONFIGUOFF = 0
  • BrickletPerformanceDC`ERRORULEDUCONFIGUON = 1
  • BrickletPerformanceDC`ERRORULEDUCONFIGUSHOWUHEARTBEAT = 2
  • BrickletPerformanceDC`ERRORULEDUCONFIGUSHOWUERROR = 3
BrickletPerformanceDC@GetErrorLEDConfig[] → config
Returns:
  • config – Type: Integer, Range: See constants, Default: 3

Returns the LED configuration as set by SetErrorLEDConfig[]

The following constants are available for this function:

For config:

  • BrickletPerformanceDC`ERRORULEDUCONFIGUOFF = 0
  • BrickletPerformanceDC`ERRORULEDUCONFIGUON = 1
  • BrickletPerformanceDC`ERRORULEDUCONFIGUSHOWUHEARTBEAT = 2
  • BrickletPerformanceDC`ERRORULEDUCONFIGUSHOWUERROR = 3
BrickletPerformanceDC@SetCWLEDConfig[config] → Null
Parameters:
  • config – Type: Integer, Range: See constants, Default: 3

Configures the CW LED to be either turned off, turned on, blink in heartbeat mode or if the motor turn clockwise.

The following constants are available for this function:

For config:

  • BrickletPerformanceDC`CWULEDUCONFIGUOFF = 0
  • BrickletPerformanceDC`CWULEDUCONFIGUON = 1
  • BrickletPerformanceDC`CWULEDUCONFIGUSHOWUHEARTBEAT = 2
  • BrickletPerformanceDC`CWULEDUCONFIGUSHOWUCWUASUFORWARD = 3
  • BrickletPerformanceDC`CWULEDUCONFIGUSHOWUCWUASUBACKWARD = 4
BrickletPerformanceDC@GetCWLEDConfig[] → config
Returns:
  • config – Type: Integer, Range: See constants, Default: 3

Returns the LED configuration as set by SetCWLEDConfig[]

The following constants are available for this function:

For config:

  • BrickletPerformanceDC`CWULEDUCONFIGUOFF = 0
  • BrickletPerformanceDC`CWULEDUCONFIGUON = 1
  • BrickletPerformanceDC`CWULEDUCONFIGUSHOWUHEARTBEAT = 2
  • BrickletPerformanceDC`CWULEDUCONFIGUSHOWUCWUASUFORWARD = 3
  • BrickletPerformanceDC`CWULEDUCONFIGUSHOWUCWUASUBACKWARD = 4
BrickletPerformanceDC@SetCCWLEDConfig[config] → Null
Parameters:
  • config – Type: Integer, Range: See constants, Default: 3

Configures the CCW LED to be either turned off, turned on, blink in heartbeat mode or if the motor turn counter-clockwise.

The following constants are available for this function:

For config:

  • BrickletPerformanceDC`CCWULEDUCONFIGUOFF = 0
  • BrickletPerformanceDC`CCWULEDUCONFIGUON = 1
  • BrickletPerformanceDC`CCWULEDUCONFIGUSHOWUHEARTBEAT = 2
  • BrickletPerformanceDC`CCWULEDUCONFIGUSHOWUCCWUASUFORWARD = 3
  • BrickletPerformanceDC`CCWULEDUCONFIGUSHOWUCCWUASUBACKWARD = 4
BrickletPerformanceDC@GetCCWLEDConfig[] → config
Returns:
  • config – Type: Integer, Range: See constants, Default: 3

Returns the LED configuration as set by SetCCWLEDConfig[]

The following constants are available for this function:

For config:

  • BrickletPerformanceDC`CCWULEDUCONFIGUOFF = 0
  • BrickletPerformanceDC`CCWULEDUCONFIGUON = 1
  • BrickletPerformanceDC`CCWULEDUCONFIGUSHOWUHEARTBEAT = 2
  • BrickletPerformanceDC`CCWULEDUCONFIGUSHOWUCCWUASUFORWARD = 3
  • BrickletPerformanceDC`CCWULEDUCONFIGUSHOWUCCWUASUBACKWARD = 4
BrickletPerformanceDC@SetGPIOLEDConfig[channel, config] → Null
Parameters:
  • channel – Type: Integer, Range: [0 to 1]
  • config – Type: Integer, Range: See constants, Default: 4

Configures the GPIO LED to be either turned off, turned on, blink in heartbeat mode or the GPIO state.

The GPIO LED can be configured for both channels.

The following constants are available for this function:

For config:

  • BrickletPerformanceDC`GPIOULEDUCONFIGUOFF = 0
  • BrickletPerformanceDC`GPIOULEDUCONFIGUON = 1
  • BrickletPerformanceDC`GPIOULEDUCONFIGUSHOWUHEARTBEAT = 2
  • BrickletPerformanceDC`GPIOULEDUCONFIGUSHOWUGPIOUACTIVEUHIGH = 3
  • BrickletPerformanceDC`GPIOULEDUCONFIGUSHOWUGPIOUACTIVEULOW = 4
BrickletPerformanceDC@GetGPIOLEDConfig[channel] → config
Parameters:
  • channel – Type: Integer, Range: [0 to 1]
Returns:
  • config – Type: Integer, Range: See constants, Default: 4

Returns the LED configuration as set by SetGPIOLEDConfig[]

The following constants are available for this function:

For config:

  • BrickletPerformanceDC`GPIOULEDUCONFIGUOFF = 0
  • BrickletPerformanceDC`GPIOULEDUCONFIGUON = 1
  • BrickletPerformanceDC`GPIOULEDUCONFIGUSHOWUHEARTBEAT = 2
  • BrickletPerformanceDC`GPIOULEDUCONFIGUSHOWUGPIOUACTIVEUHIGH = 3
  • BrickletPerformanceDC`GPIOULEDUCONFIGUSHOWUGPIOUACTIVEULOW = 4
BrickletPerformanceDC@GetSPITFPErrorCount[out errorCountAckChecksum, out errorCountMessageChecksum, out errorCountFrame, out errorCountOverflow] → Null
Output Parameters:
  • errorCountAckChecksum – Type: Integer, Range: [0 to 232 - 1]
  • errorCountMessageChecksum – Type: Integer, Range: [0 to 232 - 1]
  • errorCountFrame – Type: Integer, Range: [0 to 232 - 1]
  • errorCountOverflow – Type: Integer, Range: [0 to 232 - 1]

Returns the error count for the communication between Brick and Bricklet.

The errors are divided into

  • ACK checksum errors,
  • message checksum errors,
  • framing errors and
  • overflow errors.

The errors counts are for errors that occur on the Bricklet side. All Bricks have a similar function that returns the errors on the Brick side.

BrickletPerformanceDC@SetStatusLEDConfig[config] → Null
Parameters:
  • config – Type: Integer, Range: See constants, Default: 3

Sets the status LED configuration. By default the LED shows communication traffic between Brick and Bricklet, it flickers once for every 10 received data packets.

You can also turn the LED permanently on/off or show a heartbeat.

If the Bricklet is in bootloader mode, the LED is will show heartbeat by default.

The following constants are available for this function:

For config:

  • BrickletPerformanceDC`STATUSULEDUCONFIGUOFF = 0
  • BrickletPerformanceDC`STATUSULEDUCONFIGUON = 1
  • BrickletPerformanceDC`STATUSULEDUCONFIGUSHOWUHEARTBEAT = 2
  • BrickletPerformanceDC`STATUSULEDUCONFIGUSHOWUSTATUS = 3
BrickletPerformanceDC@GetStatusLEDConfig[] → config
Returns:
  • config – Type: Integer, Range: See constants, Default: 3

Returns the configuration as set by SetStatusLEDConfig[]

The following constants are available for this function:

For config:

  • BrickletPerformanceDC`STATUSULEDUCONFIGUOFF = 0
  • BrickletPerformanceDC`STATUSULEDUCONFIGUON = 1
  • BrickletPerformanceDC`STATUSULEDUCONFIGUSHOWUHEARTBEAT = 2
  • BrickletPerformanceDC`STATUSULEDUCONFIGUSHOWUSTATUS = 3
BrickletPerformanceDC@GetChipTemperature[] → temperature
Returns:
  • temperature – Type: Integer, Unit: 1 °C, Range: [-215 to 215 - 1]

Returns the temperature as measured inside the microcontroller. The value returned is not the ambient temperature!

The temperature is only proportional to the real temperature and it has bad accuracy. Practically it is only useful as an indicator for temperature changes.

BrickletPerformanceDC@Reset[] → Null

Calling this function will reset the Bricklet. All configurations will be lost.

After a reset you have to create new device objects, calling functions on the existing ones will result in undefined behavior!

BrickletPerformanceDC@GetIdentity[out uid, out connectedUid, out position, out {hardwareVersion1, hardwareVersion2, hardwareVersion3}, out {firmwareVersion1, firmwareVersion2, firmwareVersion3}, out deviceIdentifier] → Null
Output Parameters:
  • uid – Type: String, Length: up to 8
  • connectedUid – Type: String, Length: up to 8
  • position – Type: Integer, Range: [ToCharacterCode["a"][[0]] to ToCharacterCode["h"][[0]], ToCharacterCode["z"][[0]]]
  • hardwareVersioni – Type: Integer
    • 1: major – Type: Integer, Range: [0 to 255]
    • 2: minor – Type: Integer, Range: [0 to 255]
    • 3: revision – Type: Integer, Range: [0 to 255]
  • firmwareVersioni – Type: Integer
    • 1: major – Type: Integer, Range: [0 to 255]
    • 2: minor – Type: Integer, Range: [0 to 255]
    • 3: revision – Type: Integer, Range: [0 to 255]
  • deviceIdentifier – Type: Integer, Range: [0 to 216 - 1]

Returns the UID, the UID where the Bricklet is connected to, the position, the hardware and firmware version as well as the device identifier.

The position can be 'a', 'b', 'c', 'd', 'e', 'f', 'g' or 'h' (Bricklet Port). A Bricklet connected to an Isolator Bricklet is always at position 'z'.

The device identifier numbers can be found here. There is also a constant for the device identifier of this Bricklet.

Callback Configuration Functions

BrickletPerformanceDC@SetEmergencyShutdownCallbackConfiguration[enabled] → Null
Parameters:
  • enabled – Type: True/False, Default: False

Enable/Disable EmergencyShutdownCallback callback.

BrickletPerformanceDC@GetEmergencyShutdownCallbackConfiguration[] → enabled
Returns:
  • enabled – Type: True/False, Default: True

Returns the callback configuration as set by SetEmergencyShutdownCallbackConfiguration[].

BrickletPerformanceDC@SetVelocityReachedCallbackConfiguration[enabled] → Null
Parameters:
  • enabled – Type: True/False, Default: False

Enable/Disable VelocityReachedCallback callback.

BrickletPerformanceDC@GetVelocityReachedCallbackConfiguration[] → enabled
Returns:
  • enabled – Type: True/False, Default: False

Returns the callback configuration as set by SetVelocityReachedCallbackConfiguration[].

BrickletPerformanceDC@SetCurrentVelocityCallbackConfiguration[period, valueHasToChange] → Null
Parameters:
  • period – Type: Integer, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0
  • valueHasToChange – Type: True/False, Default: False

The period is the period with which the CurrentVelocityCallback callback is triggered periodically. A value of 0 turns the callback off.

If the value has to change-parameter is set to true, the callback is only triggered after the value has changed. If the value didn't change within the period, the callback is triggered immediately on change.

If it is set to false, the callback is continuously triggered with the period, independent of the value.

BrickletPerformanceDC@GetCurrentVelocityCallbackConfiguration[out period, out valueHasToChange] → Null
Output Parameters:
  • period – Type: Integer, Unit: 1 ms, Range: [0 to 232 - 1], Default: 0
  • valueHasToChange – Type: True/False, Default: False

Returns the callback configuration as set by SetCurrentVelocityCallbackConfiguration[].

Callbacks

Callbacks can be registered to receive time critical or recurring data from the device. The registration is done by assigning a function to a callback property of the device object:

MyCallback[sender_,value_]:=Print["Value: "<>ToString[value]]

AddEventHandler[performanceDC@ExampleCallback,MyCallback]

For further information about event handling using .NET/Link see the corresponding Mathematica .NET/Link documentation.

The available callback property and their type of parameters are described below.

Note

Using callbacks for recurring events is always preferred compared to using getters. It will use less USB bandwidth and the latency will be a lot better, since there is no round trip time.

event BrickletPerformanceDC@EmergencyShutdownCallback[sender]
Callback Parameters:
  • sender – Type: NETObject[BrickletPerformanceDC]

This callback is triggered if either the current consumption is too high or the temperature of the driver chip is too high (above 150°C) or the user defined thermal shutdown is triggered (see SetThermalShutdown[]). n case of a voltage below 6V (input voltage) this callback is triggered as well.

If this callback is triggered, the driver chip gets disabled at the same time. That means, SetEnabled[] has to be called to drive the motor again.

event BrickletPerformanceDC@VelocityReachedCallback[sender, velocity]
Callback Parameters:
  • sender – Type: NETObject[BrickletPerformanceDC]
  • velocity – Type: Integer, Unit: 100/32767 %, Range: [-215 + 1 to 215 - 1]

This callback is triggered whenever a set velocity is reached. For example: If a velocity of 0 is present, acceleration is set to 5000 and velocity to 10000, the VelocityReachedCallback callback will be triggered after about 2 seconds, when the set velocity is actually reached.

Note

Since we can't get any feedback from the DC motor, this only works if the acceleration (see SetMotion[]) is set smaller or equal to the maximum acceleration of the motor. Otherwise the motor will lag behind the control value and the callback will be triggered too early.

event BrickletPerformanceDC@CurrentVelocityCallback[sender, velocity]
Callback Parameters:
  • sender – Type: NETObject[BrickletPerformanceDC]
  • velocity – Type: Integer, Unit: 100/32767 %, Range: [-215 + 1 to 215 - 1]

This callback is triggered with the period that is set by SetCurrentVelocityCallbackConfiguration[]. The parameter is the current velocity used by the motor.

The CurrentVelocityCallback callback is only triggered after the set period if there is a change in the velocity.

event BrickletPerformanceDC@GPIOStateCallback[sender, {gpioState1, gpioState2}]
Callback Parameters:
  • sender – Type: NETObject[BrickletPerformanceDC]
  • gpioStatei – Type: True/False

This callback is triggered by GPIO changes if it is activated through SetGPIOAction[].

New in version 2.0.1 (Plugin).

Virtual Functions

Virtual functions don't communicate with the device itself, but operate only on the API bindings device object. They can be called without the corresponding IP Connection object being connected.

BrickletPerformanceDC@GetAPIVersion[] → {apiVersion1, apiVersion2, apiVersion3}
Output Parameters:
  • apiVersioni – Type: Integer
    • 1: major – Type: Integer, Range: [0 to 255]
    • 2: minor – Type: Integer, Range: [0 to 255]
    • 3: revision – Type: Integer, Range: [0 to 255]

Returns the version of the API definition implemented by this API bindings. This is neither the release version of this API bindings nor does it tell you anything about the represented Brick or Bricklet.

BrickletPerformanceDC@GetResponseExpected[functionId] → responseExpected
Parameters:
  • functionId – Type: Integer, Range: See constants
Returns:
  • responseExpected – Type: True/False

Returns the response expected flag for the function specified by the function ID parameter. It is true if the function is expected to send a response, false otherwise.

For getter functions this is enabled by default and cannot be disabled, because those functions will always send a response. For callback configuration functions it is enabled by default too, but can be disabled by SetResponseExpected[]. For setter functions it is disabled by default and can be enabled.

Enabling the response expected flag for a setter function allows to detect timeouts and other error conditions calls of this setter as well. The device will then send a response for this purpose. If this flag is disabled for a setter function then no response is sent and errors are silently ignored, because they cannot be detected.

The following constants are available for this function:

For functionId:

  • BrickletPerformanceDC`FUNCTIONUSETUENABLED = 1
  • BrickletPerformanceDC`FUNCTIONUSETUVELOCITY = 3
  • BrickletPerformanceDC`FUNCTIONUSETUMOTION = 6
  • BrickletPerformanceDC`FUNCTIONUFULLUBRAKE = 8
  • BrickletPerformanceDC`FUNCTIONUSETUDRIVEUMODE = 9
  • BrickletPerformanceDC`FUNCTIONUSETUPWMUFREQUENCY = 11
  • BrickletPerformanceDC`FUNCTIONUSETUTHERMALUSHUTDOWN = 14
  • BrickletPerformanceDC`FUNCTIONUSETUGPIOUCONFIGURATION = 16
  • BrickletPerformanceDC`FUNCTIONUSETUGPIOUACTION = 18
  • BrickletPerformanceDC`FUNCTIONUSETUERRORULEDUCONFIG = 21
  • BrickletPerformanceDC`FUNCTIONUSETUCWULEDUCONFIG = 23
  • BrickletPerformanceDC`FUNCTIONUSETUCCWULEDUCONFIG = 25
  • BrickletPerformanceDC`FUNCTIONUSETUGPIOULEDUCONFIG = 27
  • BrickletPerformanceDC`FUNCTIONUSETUEMERGENCYUSHUTDOWNUCALLBACKUCONFIGURATION = 29
  • BrickletPerformanceDC`FUNCTIONUSETUVELOCITYUREACHEDUCALLBACKUCONFIGURATION = 31
  • BrickletPerformanceDC`FUNCTIONUSETUCURRENTUVELOCITYUCALLBACKUCONFIGURATION = 33
  • BrickletPerformanceDC`FUNCTIONUSETUWRITEUFIRMWAREUPOINTER = 237
  • BrickletPerformanceDC`FUNCTIONUSETUSTATUSULEDUCONFIG = 239
  • BrickletPerformanceDC`FUNCTIONURESET = 243
  • BrickletPerformanceDC`FUNCTIONUWRITEUUID = 248
BrickletPerformanceDC@SetResponseExpected[functionId, responseExpected] → Null
Parameters:
  • functionId – Type: Integer, Range: See constants
  • responseExpected – Type: True/False

Changes the response expected flag of the function specified by the function ID parameter. This flag can only be changed for setter (default value: false) and callback configuration functions (default value: true). For getter functions it is always enabled.

Enabling the response expected flag for a setter function allows to detect timeouts and other error conditions calls of this setter as well. The device will then send a response for this purpose. If this flag is disabled for a setter function then no response is sent and errors are silently ignored, because they cannot be detected.

The following constants are available for this function:

For functionId:

  • BrickletPerformanceDC`FUNCTIONUSETUENABLED = 1
  • BrickletPerformanceDC`FUNCTIONUSETUVELOCITY = 3
  • BrickletPerformanceDC`FUNCTIONUSETUMOTION = 6
  • BrickletPerformanceDC`FUNCTIONUFULLUBRAKE = 8
  • BrickletPerformanceDC`FUNCTIONUSETUDRIVEUMODE = 9
  • BrickletPerformanceDC`FUNCTIONUSETUPWMUFREQUENCY = 11
  • BrickletPerformanceDC`FUNCTIONUSETUTHERMALUSHUTDOWN = 14
  • BrickletPerformanceDC`FUNCTIONUSETUGPIOUCONFIGURATION = 16
  • BrickletPerformanceDC`FUNCTIONUSETUGPIOUACTION = 18
  • BrickletPerformanceDC`FUNCTIONUSETUERRORULEDUCONFIG = 21
  • BrickletPerformanceDC`FUNCTIONUSETUCWULEDUCONFIG = 23
  • BrickletPerformanceDC`FUNCTIONUSETUCCWULEDUCONFIG = 25
  • BrickletPerformanceDC`FUNCTIONUSETUGPIOULEDUCONFIG = 27
  • BrickletPerformanceDC`FUNCTIONUSETUEMERGENCYUSHUTDOWNUCALLBACKUCONFIGURATION = 29
  • BrickletPerformanceDC`FUNCTIONUSETUVELOCITYUREACHEDUCALLBACKUCONFIGURATION = 31
  • BrickletPerformanceDC`FUNCTIONUSETUCURRENTUVELOCITYUCALLBACKUCONFIGURATION = 33
  • BrickletPerformanceDC`FUNCTIONUSETUWRITEUFIRMWAREUPOINTER = 237
  • BrickletPerformanceDC`FUNCTIONUSETUSTATUSULEDUCONFIG = 239
  • BrickletPerformanceDC`FUNCTIONURESET = 243
  • BrickletPerformanceDC`FUNCTIONUWRITEUUID = 248
BrickletPerformanceDC@SetResponseExpectedAll[responseExpected] → Null
Parameters:
  • responseExpected – Type: True/False

Changes the response expected flag for all setter and callback configuration functions of this device at once.

Internal Functions

Internal functions are used for maintenance tasks such as flashing a new firmware of changing the UID of a Bricklet. These task should be performed using Brick Viewer instead of using the internal functions directly.

BrickletPerformanceDC@SetBootloaderMode[mode] → status
Parameters:
  • mode – Type: Integer, Range: See constants
Returns:
  • status – Type: Integer, Range: See constants

Sets the bootloader mode and returns the status after the requested mode change was instigated.

You can change from bootloader mode to firmware mode and vice versa. A change from bootloader mode to firmware mode will only take place if the entry function, device identifier and CRC are present and correct.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

The following constants are available for this function:

For mode:

  • BrickletPerformanceDC`BOOTLOADERUMODEUBOOTLOADER = 0
  • BrickletPerformanceDC`BOOTLOADERUMODEUFIRMWARE = 1
  • BrickletPerformanceDC`BOOTLOADERUMODEUBOOTLOADERUWAITUFORUREBOOT = 2
  • BrickletPerformanceDC`BOOTLOADERUMODEUFIRMWAREUWAITUFORUREBOOT = 3
  • BrickletPerformanceDC`BOOTLOADERUMODEUFIRMWAREUWAITUFORUERASEUANDUREBOOT = 4

For status:

  • BrickletPerformanceDC`BOOTLOADERUSTATUSUOK = 0
  • BrickletPerformanceDC`BOOTLOADERUSTATUSUINVALIDUMODE = 1
  • BrickletPerformanceDC`BOOTLOADERUSTATUSUNOUCHANGE = 2
  • BrickletPerformanceDC`BOOTLOADERUSTATUSUENTRYUFUNCTIONUNOTUPRESENT = 3
  • BrickletPerformanceDC`BOOTLOADERUSTATUSUDEVICEUIDENTIFIERUINCORRECT = 4
  • BrickletPerformanceDC`BOOTLOADERUSTATUSUCRCUMISMATCH = 5
BrickletPerformanceDC@GetBootloaderMode[] → mode
Returns:
  • mode – Type: Integer, Range: See constants

Returns the current bootloader mode, see SetBootloaderMode[].

The following constants are available for this function:

For mode:

  • BrickletPerformanceDC`BOOTLOADERUMODEUBOOTLOADER = 0
  • BrickletPerformanceDC`BOOTLOADERUMODEUFIRMWARE = 1
  • BrickletPerformanceDC`BOOTLOADERUMODEUBOOTLOADERUWAITUFORUREBOOT = 2
  • BrickletPerformanceDC`BOOTLOADERUMODEUFIRMWAREUWAITUFORUREBOOT = 3
  • BrickletPerformanceDC`BOOTLOADERUMODEUFIRMWAREUWAITUFORUERASEUANDUREBOOT = 4
BrickletPerformanceDC@SetWriteFirmwarePointer[pointer] → Null
Parameters:
  • pointer – Type: Integer, Unit: 1 B, Range: [0 to 232 - 1]

Sets the firmware pointer for WriteFirmware[]. The pointer has to be increased by chunks of size 64. The data is written to flash every 4 chunks (which equals to one page of size 256).

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

BrickletPerformanceDC@WriteFirmware[{data1, data2, ..., data64}] → status
Parameters:
  • datai – Type: Integer, Range: [0 to 255]
Returns:
  • status – Type: Integer, Range: [0 to 255]

Writes 64 Bytes of firmware at the position as written by SetWriteFirmwarePointer[] before. The firmware is written to flash every 4 chunks.

You can only write firmware in bootloader mode.

This function is used by Brick Viewer during flashing. It should not be necessary to call it in a normal user program.

BrickletPerformanceDC@WriteUID[uid] → Null
Parameters:
  • uid – Type: Integer, Range: [0 to 232 - 1]

Writes a new UID into flash. If you want to set a new UID you have to decode the Base58 encoded UID string into an integer first.

We recommend that you use Brick Viewer to change the UID.

BrickletPerformanceDC@ReadUID[] → uid
Returns:
  • uid – Type: Integer, Range: [0 to 232 - 1]

Returns the current UID as an integer. Encode as Base58 to get the usual string version.

Constants

BrickletPerformanceDC`DEVICEUIDENTIFIER

This constant is used to identify a Performance DC Bricklet.

The GetIdentity[] function and the IPConnection@EnumerateCallback callback of the IP Connection have a deviceIdentifier parameter to specify the Brick's or Bricklet's type.

BrickletPerformanceDC`DEVICEDISPLAYNAME

This constant represents the human readable name of a Performance DC Bricklet.